SAE AS5179D-2023 螺母、管件、端口

NUT, FITTING, PORT

CAN/CGSB 69.19-93/ANSI/BHMA A156.3-1989 發行端口配置

La présente norme comprend les dispositifs d'ouverture de porte d'issue courant à toutes les catégories de bâtiments

Exit door opening devices

SAE AS4099A-2000 適配器，組件 端口連接環鎖定到無喇叭口管端

ADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO FLARELESS TUBE END

SAE AS5179A-2003 螺母 管件 端口

NUT@ FITTING@ PORT

SAE AS21940-2000 螺栓，叢式接頭，雙端口擴口

Bolt@ Cluster Fitting@ Double Port@ Flareless (FSC 4730)

SAE AS21940A-2015 螺栓，叢式接頭，雙端口擴口

BOLT, CLUSTER FITTING, DOUBLE PORT FLARELESS

SAE AS21940B-2024 螺栓、簇接頭、雙端口無擴口

BOLT, CLUSTER FITTING, DOUBLE PORT FLARELESS

AIA NAS 465-1978 （停用）桿端桿端外徑和管端內徑和外徑的標準尺寸和公差（修訂版 1）

(Inactive)Standard Dimensions and Tolerances for Rod End Shank Outside Diameters and Tube End Inside and Outside Diameters (Rev. 1)

SAE AS21940A-2007 螺栓，叢式接頭，雙端口擴口

BOLT, CLUSTER FITTING, DOUBLE PORT FLARELESS

SAE AS21938-2004 螺栓，叢式接頭，單端口擴口

BOLT, CLUSTER FITTING, SINGLE PORT FLARELESS

BS EN ISO 6149-1:2019 用于液壓流體動力和一般用途的連接 帶 ISO 261 公制螺紋和 O 形圈密封的端口和螺柱端 帶有用于 O 形圈密封的截頭外殼的端口

This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149-2 and ISO

Connections for hydraulic fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing-Ports with truncated housing for O-ring seal

GB/T 5652-2008 擴口式管接頭擴口端尺寸

本標準規定了擴口式管接頭擴口端尺寸。 本標準適用于管子外徑為4mm～34mm，最大工作壓力為3.5MPa～16MPa的液壓流體傳動和一般用途的管路系統

Flared couplings.Flared end

MIL MIL-P-11087F-1985 鋼管 槽口端、螺紋端或平端 (S/S BY MIL-P-11087G)

PIPE, STEEL: GROOVED, THREADED, OR PLAIN ENDS (S/S BY MIL-P-11087G)

BS EN ISO 6149-4:2014 流體動力和常規用途連接 ISO 261 公制螺紋和 O 形圈密封的端口和螺柱端部 外六角和內六角端口塞的尺寸、設計、測試方法和要求

Cross References: ISO 48 ISO 261:1998 ISO 1629 ISO 3601-3:2005 ISO 4042 ISO 4759-1:2000 ISO 5598 ISO 6149-1 ISO 6149-2 ISO 7789 ISO

Connections for fluid power and general use. Ports and stud ends with ISO 261 metric threads and O-ring sealing-Dimensions, design, test methods and requirements for external hex and internal hex port plugs

DLA MS51500 REV C-1988 鋼制37度擴口法蘭液壓管和卡套卡帽;37度擴口法蘭外螺紋管端直管轉接器

This specificationis approvedfor use by all !Jepartmentasnd Agenciesof theDepartmentof Defense.The requirementsfor acquiringthe

FITTINGS, HYDRAULIC TUBE, FLARED 37 DEGREE AND FLARELESS, STEEL; ADAPTER, STRAIGHT, PIPE TO TUBE, MALE PIPE END, 37 DEGREE FLARED [Refer To: SAE J514, SAE J514, SAE J514, SAE J514, SAE J514]